Winter-Ready HVAC Checklist: A Guide for Eden Homeowners
Quick Answer
Getting your heating system ready for winter means replacing the air filter, testing the heat before the first cold night, checking your thermostat and carbon monoxide alarms, confirming your propane or heating oil supply, clearing the outdoor heat pump unit and every vent, and scheduling a professional tune-up. Doing it in the fall gives you time to take care of any furnace repair before you depend on the heat every day.
Your Winter HVAC Checklist
A winter HVAC checklist covers eight items: the air filter, a test run, thermostat settings, carbon monoxide alarms, fuel supply, outdoor equipment, vents, and a professional tune-up. Work through them in early fall, before the first hard freeze:
- Replace the air filter and confirm it fits its slot without gaps.
- Run the heat for a test cycle and confirm warm air at every vent.
- Review your thermostat settings and replace its batteries if it uses them.
- Test every carbon monoxide alarm and replace any past its end-of-life date.
- Check your propane, heating oil, or kerosene tank level.
- Clear leaves and debris from the outdoor heat pump unit and from furnace vent pipes outside.
- Open every supply and return vent and move anything blocking them.
- Schedule a furnace tune-up or heat pump service.
As fall turns to winter in Eden and Reidsville, the checks above take an afternoon, and the professional tune-up covers the safety items you can’t inspect yourself.
Eden’s housing adds a reason to take this seriously. The city was formed in 1967 when Leaksville, Spray, and Draper merged, and its older neighborhoods include homes from the textile-mill era that began in the 1890s. Houses that old were built before central forced-air heat, so their furnaces, ductwork, and fuel tanks were added or replaced over the decades, and the equipment in them can vary widely in age and type.
Replace the Filter First
Replacing the air filter first keeps air moving freely, so the rest of the heating system doesn’t have to work harder or run hot. In a furnace, low airflow lets the heat exchanger run hotter than it should, which can trip the high-limit safety switch and shut the burner off before the house warms up. In a heat pump, low airflow reduces heating capacity and efficiency.
Regular filter replacement is the simplest item on this list. If your current filter has been in place for three months or more, check it now. Buy the replacement by the nominal size printed on the old filter’s frame, such as 16x25x1, and make sure the filter slot cover is in place so air can’t slip around the filter. Berico’s filter delivery program with FilterFetch can send the correct filter to your door, with reminder emails timed to your replacement schedule.
Test the Heat Before the First Cold Night
Test your heat in early fall by switching the thermostat to Heat and setting it two or three degrees above the current indoor temperature, which gives the system a clear call for heat while the weather is still mild. Within a few minutes, you should feel warm air at the vents.
While it runs, pay attention to these signs:
- A dusty or burning smell on the first run of the season is normal as dust burns off the heat exchanger or heating elements, and it should fade within a short time.
- A smell that lingers, smells like burning plastic or wiring, or keeps coming back means turning the system off and calling for service.
- A rotten-egg smell near a gas or propane furnace means leaving the house and calling your gas supplier or 911 from outside.
- A furnace that starts and shuts off repeatedly, or a burner that won’t stay lit, needs a technician.
If you have a heat pump, don’t be surprised if the outdoor unit goes quiet, releases steam, or blows cooler air for a few minutes on a cold day. That is the defrost cycle clearing frost from the outdoor coil, and it’s part of normal winter operation.
If the thermostat itself acts up during the test, with a blank screen, no response, or a system that won’t follow the setting, start by replacing its batteries. If the problem continues, it may be time for a new thermostat.
Check Your Thermostat Settings
The right thermostat settings in winter keep your home comfortable without wasting fuel or electricity. The U.S. Department of Energy’s Energy Saver guide suggests setting the thermostat around 68 to 70 degrees while you’re awake and lower while you’re asleep or away. It estimates that turning the thermostat back 7 to 10 degrees for eight hours a day can save as much as 10 percent a year on heating and cooling.
Heat pumps are the exception. The Department of Energy notes that setting back a heat pump in heating mode can make it run inefficiently, because recovering from a deep setback can bring on the electric backup heat, which costs more to run. With a heat pump, use a smaller setback or a thermostat designed to manage heat pump recovery. Gas, propane, and oil furnaces handle setbacks without that penalty.
Is Smart Thermostat Installation Worth It?
A smart thermostat installation pays off most when your schedule varies or you want to adjust the heat from your phone, since the thermostat can manage setbacks for you. Compatibility is the part to get right. A heat pump with backup heat needs a thermostat that supports heat pump staging, and many smart thermostats need a common wire (C-wire) for constant power, which some older homes don’t have. An installer can confirm compatibility and add wiring if needed. Berico installs and repairs thermostats.
Test Your Carbon Monoxide Alarms
Any home with a gas, propane, oil, or kerosene furnace, water heater, or fireplace, or with an attached garage, should have working carbon monoxide alarms tested before heating season. Carbon monoxide is odorless and invisible, so the alarm is your only warning.
- Press the test button on each alarm and replace batteries as needed.
- Check the manufacturer’s end-of-life date on the back of each alarm and replace any that have expired.
- Make sure there is an alarm on every level of the home and near sleeping areas, following the manufacturer’s placement instructions.
- If an alarm sounds, get everyone out of the house and call 911 from outside. Don’t go back in until responders say it is safe.
North Carolina law requires landlords to provide at least one working carbon monoxide alarm on each level of a rental home that has a fossil-fuel-burning heater, appliance, or fireplace, or an attached garage. For homeowners, the same standard is a sensible minimum.
What a Carbon Monoxide Check Covers
A professional carbon monoxide check looks for the problems that let carbon monoxide escape in the first place. During a fall visit, a technician can inspect the furnace heat exchanger for cracks, confirm the flue or vent pipe is intact and drafting properly, and test combustion to see whether the burner is producing excess carbon monoxide. Those are the safety checks a homeowner can’t do, and they matter most on older fuel-burning equipment.
Confirm Your Fuel Supply
If your home heats with propane, heating oil, or kerosene, check the tank level before the first cold snap. Most propane tanks have a gauge showing the percentage full, and heating oil tanks typically have a float gauge on top.
Running out causes more trouble than a cold night. When an oil tank runs low, the burner can draw sediment from the bottom of the tank into the fuel line and filter, and the system may need service before it will restart. When a propane system runs out, a technician may need to check the system for leaks before service is restored.
Berico’s Eden office on South Van Buren Road delivers propane, and Berico also offers heating oil and kerosene delivery. Its Autofill program tracks your usage and schedules deliveries automatically, on a year-round or seasonal schedule, so you don’t have to watch the gauge yourself.
Prepare Your Heat Pump for Winter
Scheduling heat pump service before winter confirms the system can heat efficiently and that its backup heat works when temperatures drop. A technician can check the refrigerant charge, the defrost controls, the electrical connections, and the backup heat strips that take over when the heat pump needs help.
You can handle the outdoor unit yourself. Clear away leaves, pine straw, mulch, and overgrown shrubs, and keep the clearance your unit’s manufacturer recommends around it. Don’t cover a heat pump for winter, because unlike an air conditioner, it runs all season. A light layer of frost is normal and clears during defrost. Thick ice that encases the coil and doesn’t clear is a reason to call for service.
It also helps to know what your thermostat is telling you. “Aux heat” means the electric backup strips are helping the heat pump, which is normal during defrost or a cold snap. “Emergency heat” is a setting that runs on backup heat alone; use it only if the outdoor unit fails, since it costs considerably more to run.
Check Vents Inside and Outside
Make sure every supply and return vent in the house is open and not blocked by furniture, rugs, or curtains. Free airflow is essential to good heating performance. Closing vents in unused rooms doesn’t save energy the way it seems like it should; it raises the pressure in the duct system and reduces airflow, which can make a furnace overheat and shut off on its high-limit switch.
Then check outside. A high-efficiency furnace vents through plastic intake and exhaust pipes on an exterior wall or the roof. Keep those openings clear of leaves, debris, and anything stacked against the wall, because a blocked pipe can shut the furnace down.
Schedule Your Furnace Tune-Up
A professional furnace tune-up covers the safety and performance checks that require tools and training. Replacing the filter and running a test cycle are things you can handle on your own, but the rest belongs with an experienced technician. Schedule early in the fall to get a convenient appointment before cold weather arrives.
What a visit includes depends on the equipment. For a gas or propane furnace, expect an inspection of the burners, ignition, flame sensor, heat exchanger, venting, and safety controls, along with a check of electrical connections and the blower. Oil furnaces also need attention to the burner, oil filter, and combustion. Electric furnaces and heat pumps need their heating elements, controls, and electrical connections checked. Ask what Berico’s furnace maintenance visit covers for your system, and consider a maintenance plan so the visit is scheduled every year.
“The fall tune-up is when we can actually look inside the furnace. A cracked heat exchanger or a blocked flue doesn’t announce itself, but it shows up on inspection and on a combustion test. That’s the part of winter prep a homeowner can’t do, and it’s the part that matters most for safety.”
Darrel Honeycutt, Expert HVAC Tech, Berico
Getting Your Eden Home Ready for Winter
A winter-ready home starts with the simple steps: a fresh filter, a test run, sensible thermostat settings, working carbon monoxide alarms, a full fuel tank, and clear vents inside and out. The professional tune-up adds what you can’t see, from the heat exchanger to the combustion readings, and gives you time to handle any repair before the coldest weather.
If you’d like help, Berico’s Eden office at 856 South Van Buren Road serves homeowners in Eden, Reidsville, and the rest of Rockingham County. Contact Berico’s Eden office to schedule a furnace tune-up, heat pump service, or fuel delivery before winter.
People Also Ask
When should I get my furnace serviced before winter?
Early fall is the best time, ideally before you need the heat on a regular basis. Servicing in September or October leaves time to order parts or make repairs if the technician finds a problem, rather than discovering it on the first cold night. A heat pump runs year-round, so it benefits from one visit in the spring for cooling and another in the fall for heating.
What temperature should I set my thermostat to in winter?
The U.S. Department of Energy suggests around 68 to 70 degrees while you’re awake and a lower setting while you’re asleep or away. It estimates that turning the thermostat back 7 to 10 degrees for eight hours a day can save as much as 10 percent a year. If you have a heat pump, keep setbacks smaller or use a thermostat built for heat pumps, since recovering from a deep setback can bring on more expensive backup heat.
How often should I replace my furnace filter in winter?
Standard 1-inch filters generally need replacing every one to three months, and thicker media filters last longer. Winter run times, pets, and dusty conditions shorten that interval. The most reliable approach is to check the filter monthly during heating season and replace it when the intake side looks gray and coated. Writing the date on the frame when you install it makes the next check easier.
Is a burning smell normal when I turn on the heat?
A dusty burning smell the first time you run the heat each season is normal. Dust settles on the heat exchanger or heating elements over the summer and burns off when the system fires up, and the smell should fade within a short time. A smell that lingers, smells like burning plastic or wiring, or returns every time the heat runs is not normal. Turn the system off and call for service.
Where should carbon monoxide alarms be placed?
Install at least one carbon monoxide alarm on every level of the home, with alarms near sleeping areas so they can wake you. Follow the manufacturer’s instructions for exact placement and distance from fuel-burning appliances. North Carolina requires landlords to provide at least one alarm per level in rental homes with fossil-fuel-burning appliances, fireplaces, or attached garages, and the same standard is a good minimum for any home.
Why does my heat pump blow cool air in winter?
A heat pump delivers warm air, but it isn’t as hot as the air from a gas, propane, or oil furnace, so it can feel cool on your hand even when the system is heating properly. On cold days, the heat pump also runs short defrost cycles, and the air can feel cooler for a few minutes while the backup heat compensates. If the air stays cool and the house won’t reach the set temperature, call for service.
What happens if I run out of propane or heating oil?
Running out means more than a cold house. An oil burner that runs the tank low can pull sediment into the fuel line and filter, and it may need service before it will restart. A propane system that runs out may need a leak check by a technician before service is restored. An automatic delivery program such as Berico’s Autofill tracks your usage and schedules deliveries so the tank doesn’t run dry.
Should I cover my heat pump in winter?
No. Unlike a central air conditioner, a heat pump runs all winter to heat your home, and covering it blocks the airflow it needs. Keep the area around the outdoor unit clear of leaves, pine straw, mulch, and shrubs, and follow the manufacturer’s recommended clearance. A light layer of frost is normal and clears during the defrost cycle, but heavy ice that encases the coil and won’t clear is a reason to call for service.
Do I need a furnace tune-up every year?
An annual tune-up is the best way to keep a fuel-burning furnace safe, because it includes inspecting the heat exchanger and venting and testing combustion, which are the checks that catch carbon monoxide risks. It also keeps the burner, ignition, and safety controls working reliably. Some manufacturers’ warranties require regular professional maintenance, so check your warranty terms. A maintenance plan makes the yearly visit automatic.
What’s the difference between aux heat and emergency heat?
Aux heat means the heat pump’s electric backup strips are helping it heat the house, which happens automatically during defrost cycles or very cold weather. Emergency heat is a setting you choose that shuts off the heat pump and runs on backup heat alone. It’s meant for times when the outdoor unit isn’t working, because running on backup heat alone costs considerably more. If you find yourself needing emergency heat, schedule service.




Leave a Reply
Want to join the discussion?Feel free to contribute!